Steel

The PROCEDURE FOR DPT TEST ON TRUSS discuss in this post. It is a low cost inspection method known as the  Penetration Testing ( PT ). The Cleaner, the Penetrant and the Developer are the three main materials for this DPT testing. These are all the Non toxic chemicals. And Eco friendly materials. Using these Cleaner, the Penetrant and the Developer, the DPT testing carries out.

The TRUSS is a straight interconnected structural element, triangular in the shape. It makes by welding the multiple structural elements together to form a single component or a single Structure known as the Truss. It uses to carry the heavy loads and acts like a load transfer Structure.

For these reasons It is important to make sure all the welding at joints and the connections makes properly without any flaws. There are certain PROCEDURE FOR DPT TEST ON TRUSS. The Welding is the major connection of the members. This welding makes to connect the member strongly. It should be free from all the Defects.

This Dye Penetration Testing has different names,

• Liquid Penetrate Inspection ( LPI )
• Dye Penetrant Inspection ( DPI )
• Penetration Testing ( PT )

It is a simple test. And easy test to identify the discontinuities in the welding joints. Using this DPT TEST ON TRUSS MEMBERS all the surface defects and the flaws are easily identify and rectify. This test carries out without difficulties. This is one of the oldest test for identification of the defects of welding in truss joints and the connections.

PROCEDURE FOR DPT TEST ON TRUSS

There are some important Procedures for DPT test in truss components. The PROCEDURE FOR DPT TEST ON TRUSS are as follows,

1. Pre Cleaning
2. Drying After Cleaning
3. Penetrant Application
4. Removal of Excess Penetrant
5. Drying
6. Developer Application
7. Evaluation

1. Pre Cleaning

• The specimen to test (welding joints) cleans for applying of the Dye.

• It must be free from dirt, dust, paint, oil, grease, rust, and the other foreign materials.

2. Drying After Cleaning

• The cleaned surface allows to dry for two to three minutes.

3. Penetrant Application

• The penetrant applies to the surface of the welding connections and the joints.

4. Penetrant Dwell

• The penetrant dwells three to five minutes on the surface.

5. Removal of Excess Penetrant

• Remove the excess penetrant from the surface.

6. Drying

• Make the penetrant sink into the cracks, pores, fractures, pinholes, porosity, potholes.

7. Developer Application

• Apply a thin layer of the white developer above the penetrant.

8. Indication Development

• The Defects and the flaws develops and clearly visible on to the surface of welding.

9. Inspection

• The Inspections performs after a minimum time period of ten minutes under the necessary lighting conditions.

10. Evaluation

• The discontinuities in welding joints evaluates and marks for the rectification works.

The DPT TEST ON TRUSS MEMBERS discuss in this post. DPT TEST ON TRUSS MEMBERS carries to detect the Surface cracks, fractures, pinholes, porosity, potholes, in the Truss. It is a low cost inspection method known as Liquid Penetrate Inspection ( LPI ), Dye Penetrant Inspection ( DPI ), Penetration Testing ( PT ).

MS ROOF TRUSS is a straight interconnected structural element triangular in shape. It makes by welding multiple structural elements together to form a single component or single Structure known as Truss. It uses to carry heavy loads and acts like load transfer Structure. For these reasons it is important to make sure all the welding at joints and the connections makes properly without any flaws.

DPT TEST ON TRUSS MEMBERS

Dye Penetration Testing (DPT) is a test uses to identify the discontinuities and improper welding in Truss joints.

The DPT TEST ON TRUSS MEMBERS carries to detect the cracks, fractures, pinholes, porosity, potholes, in the Truss welding joints.

Dye Penetration Testing has different names,

• Liquid Penetrate Inspection ( LPI )
• Dye Penetrant Inspection ( DPI )
• Penetration Testing ( PT )

It is a simple test. And easy test to identify the discontinuities in welding joints. Using this DPT TEST ON TRUSS MEMBERS all the surface defects and flaws are easily identify and rectify. This test carries out without difficulties. This is one of the oldest test for identification of the defects in welding in truss joints and connections.

After completions of all the welding for joints and connections of truss components, the welding slug removes. This performs using mechanical means or by chipping hammers. And cleans with a steel wire brush.

The specimen to test cleans with a cleaner, for applying of the Dye. It must be free from dirt, dust, paint, oil, grease and other foreign materials.

After this the penetrant applies to the surface by dipping, Spraying, or brushing.

And it allows to remains for three to five minutes on the member. This makes to get the penetrant sink into the cracks, pores, etc. This depends on the size of the members to test.

The excess penetrant removes from the surface and a white developer applies over the penetrant. This helps to draw penetrant out of the flaws and invisible indications is visible on surface.

Now defects like, the cracks, fractures, pinholes, porosity, potholes identifies. It is clearly visible on to the surface of the Member.

The defects like, the cracks, fractures, pinholes, porosity, potholes identifies and rectifies.

MATERIALS FOR DPT TESTING IN TRUSS discuss in this post. Dye Penetration Testing (DPT) is a test uses to identify the discontinuities in welding joints and connections. And uses to detect the cracks, fractures, pinholes, porosity, potholes.

This Dye Penetration Testing has different names,

• Liquid Penetrate Inspection ( LPI )
• Dye Penetrant Inspection ( DPI )
• Penetration Testing ( PT )

It is a simple test. And easy test to identify the discontinuities in welding joints. Using this DPT TEST ON TRUSS MEMBERS all the surface defects and flaws are easily identify and rectify. This test carries out without difficulties. This is one of the oldest test for identification of the defects in welding in truss joints and connections. There are certain STEPS FOR DPT TEST IN TRUSS for identification of defects.

MATERIALS FOR DPT TESTING IN TRUSS

The MATERIALS FOR DPT TESTING IN TRUSS are as follows,

• Cleaner
• Penetrant 
• Developer

The Cleaner, Penetrant and Developer are the three main materials for this DPT testing. These are all Non toxic chemicals. And Eco friendly materials. Using these Cleaner, Penetrant and Developer DPT testing carries out.

1. Cleaner

The Cleaner is uses to clean the surface of welding joints and connections of member. The specimen to test cleans for applying of the Penetrant in welding joints. It must be free from dirt, dust, paint, oil, grease and other foreign materials.

For this cleaning a organic chemical like acetone uses. It is a colourless and Non toxic chemical. And it is a portable material comes in spray cans and in tins.

2. Penetrant

The Penetrant is on of the main element in DPT testing. Penetrant is a Dye. Its a coloring agent. It is of a high contrast color. Penetrants are red in color. So that the indications seen clearly above the white developer. It is a water washable type. And easily cleans after testing on the materials. It sprays on the welding joints and other connections members.

It allows to remains for three to five minutes on the member. This makes to get the penetrant sink into the cracks, pores, etc. This depends on the size of the joints and connection to test.

3. Developer

The excess penetrant removes from the welding joints and other connections. And Developer applies on the welding joints and other connections of members.

The Developer is a thin layer of white in colour. The developer applies quickly on to the surface of area. And welding joints to examine on the member. This carries out with spraying. The complete area of penetrant covers with spraying the white Developer. This application of developer carries out within one to two minutes after drying of penetrant.

These are the three main materials for this DPT testing.